Basic Info.
Type
Compression Testing Machine
Oil Cylinder Position
Top
Transport Package
Standard Pack
Product Description
Machine Summary:
The micro-computer control Clamp style carton compression tester simulates the work of the schnabel
car,to determine the impact the clamp plate giving the package, then evaluate the packages' squeezing
resistance property. And this machine is widely used in kitchen ware, furniture, appliances, toys fields,
especially used in package of SEARS.
Carton Clamps Holding Testing Method of Large Products
1.Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
2.Each time the product is clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.
3. Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package. If the package is too large for the clamps to be flush to front edge (i.e., large refrigerator, tractor etc.), clamp as close to the edge as possible.
4. Clamp the product a total of 10 times in the flush orientation.
5. Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamp to be positioned 6-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.
1)Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted.
2) Exception number 2: If the product height, when placed in its normal shipping orientation, is ≤ 12 inches, the 6 x6 inch offset testing is not conducted.
6. Clamp the product a total of 10 times with the clamp in the 6 x6 inch offset position.
7. Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. If the package is too large for the clamps to be positioned 2-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.
8. Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling.
According to verdict standards, if there is one item failed the test, then put forward the "Test Failure Handling Sheet".
Clamp Compression Testing Method of Small Products
Before clamp testing, verify that the clamp for using the clamp force indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
During clamp compression testing of small products, 4 samples will be utilized as outlined below.
1. If, when oriented for clamp testing (based on the handling graphics) the sides perpendicular to the platens of a single sample ≤ 24" (61cm), then the 4 sample should be placed in a"side by side"oritentation as shown to the fig 1(with 2 samples on the bottom and 2 on the top)
2. If, when oriented for clamp testing the sides perpendicular to the platens of a single sample are >24" (61cm),, then the 4 samples should be placed in a top-bottom orientation as shown fig 2. If, when placed 4-high, any of the samples are completely above the top of the platens, that sample can be removed from clamping in this orientation only(fig 3 shows 3 MHC's ready for clamp testing with the 4th sample removed from testing in this orientation)
3. Each time the samples are clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.
4. Apply the clamp force on the samples with the platens resting on the floor and the samples flush with the front edge of the platens (see fig2). If the samples are too large for the clamps to be flush to front edge, clamp as close to the edge as possible.
5. Clamp the product a total of 10times with the clamps in the flush orientation.
6. Apply the clamp force on the packaged product with the platens in a 2×2 inch offset position(see fig 3). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamps to be positioned 2-inches from the front edge, clamp as close to this position as possible.
7. Clamp the product a total of 10 times with the clamps in the offset position.
8. Repeat the flush and 2x2 inch offset camping on all other sides of the product that are identified in the handling graphics as acceptable for clamp handling. Please note, depending on the box geometry, you may use both the side-by-side and top-bottom orientation during clamp testing.
Technical Parameter:
Model | JY-1051 Clamp style Carton Compression Tester |
Squeezing force | 50--3000kg, adjustable |
Size of the clamp plate | 1200*1200mm |
Maximum squeezing space | 1200*1200*1200mm (can be customized) |
Minimum squeezing space | 400*1200*1200 (can be customized) |
Squeezing speed | 5-50mm/min, adjustable |
Adjustable space | 100-600mm (can be customized) |
Outside dimension | 3810*1900*2100mm |
Weight | 800kg |
Power | 380V, 50Hz |
Control system | PLC or computer controller |
If you have new requirements, please contact the development department,Senior engineer to provide you with the most authoritative product testing scheme
Q1:Is your company a trading one or a factory?
A1:Our factory produces goods directly. We have focused on the development and manufacturing of physical and environmental testing equipments for 18 years,besides,we have export experience of six years.
Q2:What about the quality of services and products?
A2:Berore shipping and delivering the goods,each product must be tested and tested for 100% .
Products using training: we would provide a training video of each product in order to show you how to install and operate.
All products meet the standsrds of ISO, ASTM, AATCC, BS, EN, DIN, JIS, GB and other requirements.Q3:How long is the delivery time?A3:Usually about 15 to 25 days.If we have stock, we can arrange the shipment within 3 days.
Kindly note that our producing and delivery time depend on specific item and the number of it.
except for the special customization.
Q4:Distance transportation, the packaging is strong enough?
A4:Packing: the first layer uses bubble film ,and the second layer uses vacuum film.We take away the air so as to make a vacuum environment after packing,which can avoid the problem of rust on the rough sea,and the outer packing using standard wooden cases.
Q5: What is the mode of payment?
A5: Generally we use telegraphic transfer,inculding 50% deposit and 50% before shipment.Other payment methods can be negotiated.
Q7:How warranties and after-sales services?
A7:Our products have 18-month warranty.
Life-long free technical support, be video through email.Besides, we can help you to repair your problem controller , even it's not from our factory Produce.
What you need to do is to send us the controller.
Outside the warranty period, professional after-sales service team will provide the perfect technical support, and help customers to solve problems when using our products, deal with guest problems and complaints, and in a professional and timely.
Commitment:
Though we sign a contract, we will also sign a letter of commitment, which will increase your confidence in us.
Address:
Dn-32, Dn-33, Jingshan Third Industrial Zone, Chashan Town, Dongguan, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Instruments & Meters, Manufacturing & Processing Machinery
Management System Certification:
ISO 9001
Company Introduction:
JunYuan mechanical equipment Co., Ltd. Belong to chun yen(OTS) company, which is Taiwan brand. Manufacturer In Dongguan. Taiwan Technology. High-end products, founded in 1998. Our company collection of r &d, production and sales in the integration of international high-tech enterprise, testing instruments and equipment directly manufacturer, the main products: Thermal shock chamber, Temperature & Humidity chamber., tensile testing machine, compressive strength testing machine, digital tensile testing machine, etc.
Our company uphold the "quality of service first, integrity-based" business philosophy, successfully developed belongs to JunYuan company own brand. Dedicated to the world standard: ISO, ASTM, DIN, EN, BS, JIS, GB, ANSI, UL, TAPPI, AATCC, IEC, VDE...All used. International level quality synchronization competition with the advanced world trade; Product innovation, technology outstanding!
Our head office is located in Taiwan, China production base is in DongGuan, factory building area of 10000 square meters. Our products with their accuracy and reliability are chosen by the majority of industry and scientific research institutions. Welcome to visit our factory! Company goal: To become the leading world and high trust test equipment supplier!